How do you refinish an old pie safe?

How do you refinish an old pie safe?

How to Refinish a Pie Safe

  1. Remove all the hardware and the screening using your screwdriver.
  2. Clean the pie safe to remove any debris.
  3. Brush on a commercial stripper.
  4. Sand the surface of the pie safe starting with a 180-grit sandpaper.
  5. Wipe off the surface of the pie safe to remove all traces of sawdust.

How tall are pie safes?

Design. A common pie safe is made of wood, is around the same size as a large bureau, and is approximately 18 inches (46 cm) deep.

What was the purpose of a pie safe?

As the name implies, pie safes were originally used to safely store pies, bread, and other perishable food items. Typically about 18 inches deep, these storage cupboards feature multiple shelves that are protected by two hinged doors.

How do you clean a pie tin?

How to Clean Punched Tin on a Pie Safe

  1. Clean the tin as much as possible using a solution of hot water and dish soap, scrubbing with a plastic-bristle scrub brush.
  2. Remove tarnish by spraying the tin with tarnish remover and buffing the tarnish away with a soft, dry towel.

How do you restore a punched tin?

Blow the tin with a hair dryer set on warm for a few minutes to ensure the tin panel is completely dry, inside and out. Apply a small amount of car wax to your tin doors with a soft cloth. Rub it in well using a circular motion. Use a dry cloth to remove excess wax and buff the tin to a shine.

What is the difference between a jelly cupboard and a pie safe?

A pie safe, also called a kitchen safe, is easy to identify. It is a rectangular cupboard, usually with two doors that have pierced tin panels. A jelly cupboard is a Midwestern term for a two-drawer, two-door kitchen cupboard used for storage. In all other parts of the country, it is known as a cupboard.

How do you restore old tin?

Mix 2 tablespoons of baking soda and 1 cup hot water to create a paste for larger tarnished areas of your tin. Apply the paste onto specific areas and allow it there for a few minutes before lightly scrubbing it with your rag.

How do you clean an old punched tin?

Wash punched tin with a soft rag, cold water and a mild dish detergent only if stubborn dirt, grime or grease won’t come off with a dry rag. Rinse the tin with cold water after using a detergent. Wipe off excess moisture immediately after cleaning tin with water. Use a soft, dry cloth.

How do you clean a pressed tin?

The pressed metal is easy to clean when left in the raw finish by simply wiping over with warm soapy water using a soft cloth or sponge (no scourers) and drying with a soft microfiber cloth. Do not use any scourer or abrasive cleaners as these will scratch the aluminium.

Does vinegar remove rust?

You can use white vinegar for effective rust removal. The rust reacts with the vinegar and later dissolves. Simply soak the rusty metal object in white vinegar for a couple of hours and then just wipe to remove the rust. Using regular vinegar is also an option, however, it will take more time to remove the rust.

How do you remove tarnish from tin?

A dab of white, non-gel toothpaste on a damp cloth or toothbrush and gently rub/brush. Mix 2 tablespoons of baking soda and 1 cup hot water to create a paste for larger tarnished areas of your tin. Apply the paste onto specific areas and allow it there for a few minutes before lightly scrubbing it with your rag.

What is the best homemade rust remover?

Simply soak the rusty metal object in white vinegar for a couple of hours and then just wipe to remove the rust. If the object is too large, simply pour white vinegar evenly over the surface of the object and give it some time to settle.

Does WD-40 Remove rust?

WD-40 Specialist® Rust Remover Soak quickly dissolves rust and restores tools, equipment, and surfaces to bare metal without chipping, scraping or scrubbing. Great for removing rust from tools, metal, cast iron, chrome parts, and more without harming paint, gaskets, trim, or other surrounding parts.

How do you get rid of old rust signs?

Mix 1 part water with 1 part white vinegar in a spray bottle. Spray any remaining stains on the sign and wipe with the towel to remove them. Apply rust remover to a damp cloth. Scrub any rust spots on the sign with the cloth according to label instructions, to prevent stripping the old metal sign’s paint.

Related Posts